Pay attention to work detailsImprove service quality

Operation manual of rewinding machine

A. Overview.

Performance and features:

Single shaft rewinding machine is used for double-sided tape. Rewinding of American paper, kraft paper, sea surface tape, PVC protective film, etc.

The machine is light. Small size, low noise. Efficient energy saving, fast dynamic response, stable operation speed.

This machine adopts frequency conversion to regulate speed and fully integrated circuit control. Complete functions, good repeatability, stable speed. Reliable. Absolute action.

Pressure control is used to control winding tension. Two - section electronic length, length calculation is accurate. .

Main technical parameters.

Dimensions: length * width * height (2600*1500*1300)

Weight: about 500kg

Power: 20 kw - 380 - v

External pressure: 5 kg/c ㎡.

Reel tube: 3"

Effective winding width: 1600mm.

2. Schematic diagram of electrical principles (omitted)

3. Installation precautions:

1. The operator should read the instruction carefully before operation.

2. Check whether the four-leg mounting of the rewinder is stable and the body has no grounding wire.

3. The machine should be installed in a dry and ventilated place, and the distance between the surrounding objects should be greater than 2m

4. Connect the safety grounding terminal of the rewinder with the grounding protection line reliably, and the joint must be tightened

5. This machine must have special person to be responsible for, special person to use.

Four. Panel function diagram

Reset speed display. (2) reset. Meter length count. Indicates winding tension. Tape tension indicator. Upper and lower front thimble

Adjustment of winding tension. Remove the tension adjustment. E power switch. Attending to start. Running stop/inching. Speed adjustment.

[13] scram.

Five. Action steps.

1. Connect the inlet pipe to the air inlet port of the air filter of the rewinding machine and connect the input power.

2. Turn on the power switch on the control panel.

3. Set the length of rewinding as follows.

A. According to the SET, AL mamas appear at a time

B. For example, if you are looking for a supply of food, if you are looking for a supply of food, you may find a supply of food.

The second section is the frequency converter deceleration section, generally the second section is larger than the first section 1---2 meters. For example; The length of rewinding is 50 meters per roll. AL is set to 48 meters, SE to 50 meters.

After pressing the reset key, you can count again.

4. Paper tape.

A. Main volume: over pressure: optic axis: over transportation stick: over; anti-sticking roller:

5: put the paper tape on, wrap the paper tube on the rewind reel, and turn the air gun on the rewind expansion shaft's blow-off nozzle until the paper tube cannot slip. Adjust the reeler on the control panel and the air pressure of reeler to make the reeler tighten properly.

Manual table cutting instruction.

Overview, performance and features.

1. This machine is used for the cutting of American tape, double-sided tape and sponge kraft tape in the tape industry, as well as the cutting of clothing industry's roller skin and trademark cloth.

1. The chuck is a manual chuck, easy to operate;

2. The guide rod material is 38 cr-molybdenum al nitriding treatment wear-resisting strength is high, transversely USES the linear bearing operation, is flexible and handy;

3. The sliding seat is cast member, compact and compact.

4. Cutting method with a diameter of 250mm circular knife; .

5. There are six specification options for cutting width.

6. The cutting width is 1600mm and the maximum cutting diameter is 150mm.

2. Main technical parameters:

Dimensions (length * width * height) 2500*1250*800.

Weight about 250kg.

Power 380v-- 1.5kw three-phase four wire.

3. Schematic diagram of electrical principles (omitted).

Four. Installation precautions:

1. The operator should read the instruction carefully before operating.

2. Check whether the four-leg mounting of the coiler is stable and the body is grounded.

3. The machine should be installed in a dry and ventilated place. The distance of the surrounding object should be greater than 2m.

4. Connect the safety earthing terminal of the coiler with the earthing protection line reliably, and the joint must be tightened.

5. This machine should be responsible for a dedicated person, dedicated to use.

Five. Function diagram of panel (omitted)

Six. steps

(1). The intake pipe manually cut access to the air filter inlet interface, adjust the inlet pressure is 4 kg/C ㎡.

Measure the number of marks required to adjust the hexagonal axis.

Insert the rewinding machine into the driving shaft of the cutting table. Clip the paper roll with a special handle. Press button to start the power supply, turn the hand wheel of the cutter to start the roll.

Seven; Matters needing attention:

(1). Before starting up, check whether the garden knife is vertical. Its regulation method; Rotating cutter disk, the pointer moves within 10 wires from side to side.

(2). The knife plate holder can not be loose and axial channeling and so on, otherwise there will be two knives.

(3). Lubricate the round knife and prevent the adhesive from sticking to the blade.